Rki-instruments Beacon 200 RIg Monitor, H2S/H2S Manuel d'utilisateur Page 16
- Page / 51
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11 • Beacon 200 Rig Monitor Operator’s Manual
• DC In Terminal Strip. The DC in terminal strip is a 3-point terminal strip
located above the controller terminal strip (see Figure 1). It facilitates
wiring from the 12 VDC battery. The 50 foot battery cable is factory
wired to this terminal strip. Table 4 lists the function of each terminal.
Relays
The Rig Monitor includes four channel relays (two per channel) and three
common relays. Both sets of relays are single-pole, double-throw (SPDT)
and are rated for 10 amps at 250 VAC (resistive).
NOTE: You can select normally energized (NE) or normally de-energized
(NDE) settings for each channel in the Channel Control and Setup
program. This section describes the default setting: normally de-
energized.
The alarm 1 and alarm 2 common relays are factory-set as NDE
and the fail common relay is factory-set as NE. The alarm 1, alarm
2, and fail common relays’ NE/NDE settings are not user-
adjustable.
• Channel relays. The four channel relays are above the alarm terminal
strip (see Figure 1). These relays are dedicated to specific channels
and alarm levels.
For example, the channel 1, alarm 1 relay energizes if channel 1
recognizes an alarm 1 condition. Figure 4 below illustrates the
allocation of the channel relays.
Table 4: Terminal Assignments for the AC In Terminal Strip
Terminal Connects to:
+ White wire from battery cable
- Black wire from battery cable
Earth ground, factory wired
K5 K6 K7
Channel 2, Alarm 1
Channel 1, Alarm 2
Channel 1, Alarm 1
K1 K2 K3
Common Alarm 1
Common Alarm 2
Common Fail
K4
Channel 2, Alarm 2
Figure 5. Beacon 200 Rig Monitor Channel Relay Allocation
- Hydrogen Sulfide 1
- Beacon 200 Rig Monitor 1
- Operator’s Manual 1
- Product Warranty 3
- Table of Contents 4
- Chapter 1: Introduction 6
- ~ Vac (AC voltage) 7
- Specifications 8
- Chapter 2: Description 9
- External Description 10
- 12 VDC Battery Cable 12
- Internal Description 13
- Program Buttons 14
- Main PCB 15
- Terminal Connects to: 16
- Power Converter 17
- Overview 18
- Mounting the Beacon 200 Rig 18
- BEACON 200 19
- 14.2 Max 20
- Wiring the Beacon 200 Rig 21
- Connecting External Alarms 22
- Connecting a Recorder 23
- Chapter 4: Operation 25
- Recorder Output Operation 26
- Alarm Indications 27
- Alarm 1 Condition 28
- Alarm 2 Condition 29
- Fail Condition 29
- Low Battery Condition 30
- Readings 31
- Setting Description 33
- Configure Channel Settings 34
- View System Information Menu 36
- Chapter 6: Maintenance 37
- Preparing for Calibration 38
- Adjusting the Span Setting 40
- Adjusting Strobe/Horn Volume 42
- Audio Select Switch 43
- Strobe Brightness Switch 43
- (DO NOT ADJUST) 43
- Replacing Components of the 44
- Rig Monitor 44
- Replacing the Plug-In H 45
- S Sensor 45
- Replacing the Gas Detector 45
- Preventive Maintenance 46
- Troubleshooting 48
- Slow or No 50
- Response/ 50
- Difficult or 50
- Unable to 50
- Calibrate 50
- Parts List 51
Produits connexes et manuels pour Capteurs Rki-instruments Beacon 200 RIg Monitor, H2S/H2S
(54 pages)Philips HF321 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Gesundheit und Hygiene Philips HF321.
Wir stellen 1 PDF-Handbücher Philips HF321 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels